TMP-HKDA SERIES DESICCANT AIR DRYER ( HEATLESS )

HKDA series non-heating chemical driers have -40°C fixed (-70°C optional) dew point. These driers are fit for applications needing clean and quite dry compressed air. You need to use inlet and outlet filters with the driers. By means of it, you will make sure that compressed air is clean and also humectants in the product are maintained.
Perfect operation of the product is guaranteed owing to safe electronic controller on the product. HKDA non-heating type of chemical drier is equipped with special valves and high-quality humectants. In addition to these characteristics, these products are the chemical driers with the lowest pressure decrease in the market.

Working principle

These products with the double-tank separate the water in the compressed air by means of humectants with wide surface area/mass and high hygroscopic impact resistance continuously. Drying process is performed as while one of the tanks dries the compressed air, 18% of dried air is transferred to the other tank via an orifice and this tank is regenerated. No heater is used during regeneration. Tank where the dehumidifier saturated with moisture is dried via the super dry air at atmospheric pressure. Rate of ejecting air of the absorbers (by the required dew point) can be adjusted by the operating conditions of the drier.
Super dry air is transferred to the tank with wet dehumidifier in the reverse direction and by this means, water held in the humectants is separated. HHKDA type driers equalize the pressure before replacing the tank. Surge pressure in the line and wear of humectants is prevented. Tank to hold the moisture again is pressurized again before starting to hold the moisture. Direction of flow at the moment of re-pressurizing and at the moment silencer discharges the moisture is top-down however, it is the reverse direction of the air at the moment of drying.
 

TMP-HKDA SERIES DESICCANT AIR DRYER ( HEATLESS ) 
Model Capacity (m3/min) Max. Working Pressure
(bar)
Connection Dia
(inch)
Voltage Dew Point
( °C)
Max. Inlet Temperature
(°C)
Filter Set Dimensions (W*L*H) (mm) Weight(kg)
TMP-HKDA 130 2,2 10 1" 380/3 -40 45 EXCLUDED 600 x 814 x 1312 160
TMP-HKDA 185 3,1 10 1" 380/3 -40 45 EXCLUDED 600 x 808 x 1566 180
TMP-HKDA 250 4,2 10 1" 380/3 -40 45 EXCLUDED 760 x 772 x 1580 200
TMP-HKDA 300 5 10 1 1/2" 380/3 -40 45 EXCLUDED 690 x 900 x 1558 250
TMP-HKDA 360 6 10 1 1/2" 380/3 -40 45 EXCLUDED 698 x 900 x 1558 250
TMP-HKDA 440 7,4 10 1 1/2" 380/3 -40 45 EXCLUDED 698 x 900 x 1759 340
TMP-HKDA 575 9,6 10 1 1/2" 380/3 -40 45 EXCLUDED 680 x 900 x 1991 500
TMP-HKDA 680 11,4 10 2" 380/3 -40 45 EXCLUDED 680 x 960 x 2216 535
TMP-HKDA 850 14,2 10 2" 380/3 -40 45 EXCLUDED 857 x 1016 x 2277 750
TMP-HKDA 1000 16,7 10 2" 380/3 -40 45 EXCLUDED 1010 x 1075 x 2386 755
TMP-HKDA 1250 20,8 10 DN80 380/3 -40 45 EXCLUDED 11000 x 1294 x 2413 1000
TMP-HKDA 1500 25 10 DN80 380/3 -40 45 EXCLUDED 1010 x 1300 x 2547 1050
TMP-HKDA 1800 30 10 DN80 380/3 -40 45 EXCLUDED 1110 x 1513 x 2479 1215
TMP-HKDA 2200 36,6 10 DN80 380/3 -40 45 EXCLUDED 1110 x 1460 x 2793 1550
TMP-HKDA 2700 45 10 DN80 380/3 -40 45 EXCLUDED 1252 x 1533 x 2831 1890
TMP-HKDA 3200 53,3 10 DN100 380/3 -40 45 EXCLUDED 1212 x 1653 x 3054 2240
TMP-HKDA 3600 60 10 DN100 380/3 -40 45 EXCLUDED 1210 x 1635 x 3268 2330
TMP-HKDA 4400 72,3 10 DN100 380/3 -40 45 EXCLUDED 1535 x 1905 x 2910 3000
TMP-HKDA 5000 83,3 10 DN125 380/3 -40 45 EXCLUDED 1714 x 1843 x 3382 3180
TMP-HKDA 6300 105 10 DN150 380/3 -40 45 EXCLUDED 1693 x 2114 x 3328 3450
TMP-HKDA 7200 120 10 DN150 380/3 -40 45 EXCLUDED 1795 x 2518 x 3047 3600
TMP-HKDA 8800 146,6 10 DN150 380/3 -40 45 EXCLUDED 1795 x 2518 x 3341 3850
TMP-HKDA 10800 180 10 DN200 380/3 -40 45 EXCLUDED 1875 x 2583 x 3747 4200